Cisco GLC-ZX-SM 1000BASE-ZX GBIC Interface Card (новые, оригинальные)

Cisco GLC-ZX-SM 1000BASE-ZX GBIC Interface Card  (новые, оригинальные)Увеличить

Розничная цена 4.500 ₽($)
Специальная цена товара 990 ₽($)
в наличии на складе в Москве

работает на стандартном ономодовом оптоволокне на расстояния до 70 км.

Cisco GLC-ZX-SM 1000BASE-ZX GBIC Interface Card

 

Cisco SFP (Small Form-factor Pluggable) предназначены для установки в слот маршрутизатора или коммутатора и обеспечивают подключение его к сети с помощью нужного интерфейса. Конверторы SFP поддерживают режим горячей замены (hot-swap). Выускаются различные модули, позволяющие подключить необходимое оборудование к различным средам передачи: многомодовое оптоволокно , одномодовое оптоволокно, витая пара.

Модуль GLC-ZX-SM cтандарта 1000BASE-ZX SFP работает на стандартном ономодовом оптоволокне на расстояния до 70 км. При использовании оптоволокна повышенного качества протяженность линии может достигать 100 км. Максимальное расстояние зависит от качества оптоволокна, количества сварок, качества разъемов.
Если модуль используется на расстояниях меньше, чем 25-30 км, необходимо предусмотреть установку оптических аттенюаторов на обоих концах оптической линии, это позволит избежать перегрузки модуля приемника в конверторе.

Основные возможности:

  • возможность горячей замены
  • DFB Лазер
  • двойной LC разъем
  • одно напряжение питания + 3.3В и LVPECL уровни интерфейса данных
  • LVTTL логический уровень сигнала RX LOS
  • безопасности лазера класса 1 c EN 60825-1
  • детальная информация о модули в EEPROM
  • EMI и ESD защита
  • соответствие спецификации SFP MSA и SFF-8472

    Технические характеристики:

  •  
  • выходная мощность передатчика: -9.5 ~ -3 dBm
  • чувствительность приемника: -22 dBm
  • длина волны 1550 нм
  • скорость передачи данных: 100Mbps~ 1,25Gbps
  • максимальная длина двухволоконного одномодового оптического кабеля : 100 km
  • рабочая температура: 0~50 °C
  • напряжение питания: +3.3 V
  • разъемы для оптического кабеля: двойной LC


Introduction

The industry-standard Cisco® Small Form-factor Pluggable (SFP) Gigabit Interface Converter is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking the port with the network (Figure 1). SFPs can be used and interchanged on a wide variety of Cisco Systems® products and can be intermixed in combinations of 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.

  • 1000BASE-SX SFP FOR MULTIMODE FIBER ONLY
    The 1000BASE-SX SFP, compatible with the IEEE 802.3z 1000BASE-SX standard, operates on 50 ?m multimode fiber links up to 550 m and on 62.5 ?m FDDI-grade multimode fibers up to 220m.
  • 1000BASE-LX/LH SFP FOR BOTH MULTIMODE AND SINGLE-MODE FIBERS
    The 1000BASE-LX/LH SFP, compatible with the IEEE 802.3z 1000BASE-LX standard, operates on standard single-mode fiber-optic link spans of up to 10 km and up to 550 m on any multimode fibers.
  • 1000BASE-ZX SFP FOR LONG-REACH SINGLE-MODE FIBERS
    The 1000BASE-ZX SFP operates on standard single-mode fiber-optic link spans of up to approximately 70 km in length. The SFP provides an optical link budget of 23 dB, but the precise link span length depends on multiple factors such as fiber quality, number of splices, and connectors.

    When shorter distances of single-mode fiber are used, it may be necessary to insert an inline optical attenuator in the link to avoid overloading the receiver. A 10-dB inline optical attenuator should be inserted between the fiber-optic cable plant and the receiving port on the SFP at each end of the link whenever the fiber-optic cable span loss is less than 8 dB.
  • 1000BASE-BX10-D AND 1000BASE-BX10-U SFP FOR SINGLE-FIBER BIDIRECTIONAL APPLICATIONS
    The 1000BASE-BX-D and 1000BASE-BX-U SFPs, compatible with the IEEE 802.3ah 1000BASE-BX10-D and 1000BASE-BX10-U standards, operate on a single strand of standard single-mode fiber.
  • A 1000BASE-BX10-D device is always connected to a 1000BASE-BX10-U device with a single strand of standard single-mode fiber with an operating transmission range up to 10 km.
    The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices as depicted in Figure 2: 1000BASE-BX10-D transmits a 1490 nm channel and receives a 1310 nm signal, whereas 1000BASE-BX10-U transmits at a 1310 nm wavelength and receives a 1490 nm signal. Note in Figure 2 the presence of a wavelength-division multiplexing (WDM) splitter integrated into the SFP to split the 1310 nm 1490 nm light paths.

The GLC-BX-D and GLC-BX-U SFPs also support digital optical monitoring (DOM) functions according to the industry-standard SFF-8724 Multi Source Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.

TECHNICAL SPECIFICATIONS

Platform Support
The Cisco SFPs are supported across a variety of Cisco switches, routers, and optical transport devices. For more details refer to the document SFP Compatibility Matrix.

Connectors and Cabling
Connectors include the following:

  • Dual LC/PC connector (1000BASE-SX, 1000BASE-LX/LH, and 1000BASE-ZX)
  • Single LC/PC connector (1000BASE-BX-D and 1000BASE-BX-U)

Note: Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported.

Note: Patch Cables need to be compliant with GR326.

 

 

 

SFP Port Cabling Specifications

 

Product

Wavelength (nm)

Fiber Type

Core Size (?m)

Modal Bandwidth (MHz* Km)

Operating Distance (m)

1000BASE-SX
850
MMF
62.5
160
220 (722 ft)
62.5
200
275 (902 ft)
50
400
500 (1,640 ft)
50
500
550 (1,804 ft)
1000BASE-LX/LH
1310
MMF*
62.5
500
550 (1,804 ft)
50
400
550 (1,804 ft)
50
500
550 (1,804 ft)
SMF
-**
-
10,000 (32,8210 ft)
1000BASE-ZX
1550
SMF
-
-
Approximately 70 km depending on link loss
1000BASE-BX-D
1310
SMF
-**
-
10,000 (32,821 ft)
1000BASE-BX-U
1490
SMF
-**
-
10,000 (32,821 ft)

 

* A mode-conditioning patch cord, as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning patch cord for 62.5 ?m fibers has a different specification from the mode-conditioning patch cord for 50 ?m fibers.
** ITU-T G.652 SMF as specified by the IEEE 802.3z standard.

Optical Specifications

Table 2. Main Optical Parameters

Product

Transmit Power (dBm)

Receive Power Range (dBm)

1000BASE-SX
-3 to -9.5
0 to -17
1000BASE-LX/LH
-3 to -9.5
-3 to -20
1000BASE-ZX
+5 to 0
0 to -23
1000BASE-BX10-D
1000BASE-BX10-U
-3 to -9
-3 to -19.5

 

Dimensions

Dimensions (H x W x D): 8.5 x 13.4 x 56.5 mm

Environmental Conditions and Power Requirements

Operating temperature range:

. Commercial temperature range (COM): 0 to 70°C (32 to 158°F)

. Extended temperature range (EXT): -5°C to 85°C (23 to 185°F)

. Storage temperature range: -40 to 85°C (-40 to 185°F)

Table 3 gives electrical parameters and Table 4 gives temperature range and DOM support information for the SFPs.

Electrical Parameters

Parameter

Symbol

Minimum

Typical

Maximum

Units

Supply Current

Is

-

200

300

mA

Surge Current

ISurge

-

-

30

mA

Input Voltage

Vcc

3.1

3.3

3.5

V

 

Temperature Range and DOM Support

Product Number

Temperature Range

DOM

GLC-SX-MM
COM
No
GLC-LH-SM
COM
No
GLC-ZX-SM
COM
No
GLC-BX-U
COM
Yes
GLC-BX-D
COM
Yes
SFP-GE-S
EXT
Yes
SFP-GE-L
EXT
Yes
SFP-GE-Z
EXT
Yes
вот тут сводная х-ка всех моделей какие существуют и отличия https://community.fs.com/ru/blog/how-many-types-of-sfp-transceivers-do-you-know.html

Задать вопрос о товаре  - отвечаем в течении нескольких часов.

Также рекомендуем следующие товары:

С данным товаром также покупают: